MAA-1

MSRP:US $99

Mobile phone on good volume.

No batteries! No any other power supplies!
For mobile phones, Computers and MP3 players!

 

〈 ↑ Click to enlarge 〉

 

 

使用例イメージ

 

EX METAL 50

Of the metal, By the metal, For the metal…
True Metal Heads

EX-Metal 50 is the ultimate high-gain amplifier of the metal, by the metal, for the metal heads all over the world.

 

This head cabinet is made of true metal material. It’s consists of brilliant rolled aluminium plates.
Aluminium plates are helpful for reducing weight and improving thermal radiation.

 

 

TECHNICAL DETAILSVIDEOSPEC

EX Metal 50Setting example EX Metal 50 + Metal Cab 1×12

Preamplifier section

The pre amp section has completely independent 2 channels, ultra high gain channel & crystal clean channel.
Channel 2 is this amplifier’s main mode. Its provides shredding riff, and technical guitar solos.
With our product “Metal Cab 1×12”, Players can obtain more clear tone and more rich sustained tone.
Channel 1 is also important for expressing quietness.With “Metal Cab 1×12”, players will feel fantastic crystal and acoustic tone.
Off course, sound signal gain stages are 100% tube electrical circuits.
(Only rictifier circuits are consisted of silicon diodes)

Equipped tube buffered FX Loop

 

In order to enable that guitarists can play technical licks which needs effectors such as delay,
This amplifier head equipped with an effect loop.
The effect loop is also composed of single 12AX7 tube buffer circuit and amplification circuit.

Preamplifier section

A power amp section is configred with Fixed-bias, classAB-push-pull double power tubes. It delivers over 50W power.
The stock power tubes are 6L6GC, but players can use EL34 operetating the bias-select switch.

 

“Cooming Soon!”

<EX METAL 50

Volume wattage:50W
Power tube type:1x 12AX7, 2x6L6GC (or EL34)
Preamp tube type:5x 12AX7
Channels:2 channels (CH-1/clean CH-2/ultra high gain)
Speaker output jacks:1×8 Ohms 1x16ohms
Current wattage: 00W
Dimentions:8/ 5/8″(22cm)H x 16 1/8″(41cm)W x 11 7/16″(29cm)D
Weight:34 Lbs (15.4Kg)

METAL CAB 1×12


overvirew

“METAL CAB” is a guitar speaker cabinet made of metal, as its name suggests.
The cabinet made of aluminum and carbon panels: Unprecedented in the guitar amplifier cabinet structure.
In the development of the cabinet, we pursued cabinet material itself, while adopting the “Helmholtz Resonance Cabinet” of VirtuosOn own development.

 

almi&carbonThe cabinet is made of luxuriously aluminum panel and carbon baffle boards, inspired by the racing and motorcycles.

 

TECHNICAL DETAILSVIDEOSPEC

METAL CAB 1×12

Setting example EX Metal 50 + Metal Cab 1×12

Since this cabinet is equipped with a large & heavy 12-inchs speaker which is frequently used in guitar amp,
We must beware of rigidity and saving weight than the Type-1’s.
Of course, same structure cabinet can be manufactured by using ordinary wood,
but here we are considering to produce using materials that were not generally in conventional guitar amplifier cabinet.
Although this is not a story of musical instruments, it’s common sense to use aluminum chassis and carbon fibre fairings in the world of racing and motorcycles,
to realize light weight and better rigidity.
In the development of Type-M-Cabinet, inspired by these racing motorcycles, we combined aluminum cabunet boards with carbon baffles.

 

type-M_Cabinet_CloseUp

As a result, the aluminum cabinet emphasizes the metallic tone that electric guitar has originally.
In addition, we discovered that carbon baffles could support “warmth” and “mellowness” the tube amp has.
We have produced our own structure and material speaker cabinet with “you have ever seen”.

 

In the process of development, we collected data of the ultimate acoustic guitar,
such as Martin D-45E.MartinD-45E

Learn More “Helmholtz Resonance Cabinet”

Metal – band mixed

 

Metal – Riff

<Type-M-Head

 

Volume wattage:5W

Power tube type:1x6V6S (1x6L6GC avairable)

Preamp tube type:4x12AX7

Channels:2 channels (CH-1/clean CH-2/distortion)

Speaker output jacks:1×8 Ohms 1x16ohms

Current wattage:41W

Dimentions:8″(20cm)H x 16 3/16″(41cm)W x 11 1/16″(28cm)D

Weight:13.5 Lbs (6.1Kg)

<Type-M-Cabinet>

 

Available Formats:1*12 semi-closed back cabinet

Rated Power:50W

Materials:AL5052 Aluminium & Carbon fibre

Preamp tube type:4x12AX7

Speaker & Impedance:1×12″ Jensen C12N / 8 Ohms

Current wattage:30W

Dimentions:19 3/16″(48cm)H x 18″(45cm)W x 10 3/16″D (without handles and rubber feets)

Weight:28.9 Lbs (13.1Kg)

Type-1

virtuoson type-1

overvirew

An acoustic tube amp for the electric guitar & acoustic electric guitar, specializing in the clean tone.
We’ve completed the “Type-1” guitar amplifier with more advanced tone.

The Type-1’s electrical circuit has 100% tube circuit to amplify sounds with traditional guitar amp styles.

Type-1_back_view

The cabinet has a proprietary structure “Helmholtz Resonance Cabinet”.
Double buffeled structure actively use its resonance inside.
It pursues its own tone with unique structure that conventional guitar amps could not obtain until now.

We succeeded to fit the cabinet body into the LP record jacket size of 12″ * 12″ (30cm*30cm),in the design using the latest 3D-CAD software. 
VirtuosOn_3D-CAD

Into the era “On – Plugged”

Type-1 was developed suite for solid guitar, but middle of development, we plugged acoustic-electric guitar in the TYPE-1.
Its sound should be said “another face” with the acoustic-electric guitars.
Off course, every guitarist knows acoustic-electric guitar can sounds enough with its own selfs without an amplifire.
But you can find not only amplification but wide spread sound with Type-1’s tube saturation and resonance of “Helmholtz Resonance Cabinet”are added on.
Please experience new “On – Plugged”sound a completely different from formoer guitar amplifiers.

Extraordinary tone at your home

Most guitar players are worrying about amplifier’s ludouness for their family and neighbours.
Because general type of cabinet is comfortable with its maximam powered sound.
At this point, our cabinet has enough resonance with minimam volume when players are playing in their rooms.
Of course, our cabinet is fit for loud volume in the studio & live perfomance with its extraordinalresonance.
Please experiment our guitar amps in your home, studio and stages.

 

TECHNICAL DETAILSVIDEOSPECDownload

Amplifire Section

We offer you smooth and quick responsible sound with the tube circuits.
The clean tone is comfortable, and if you use your favorite stomp box, you can make clear, crunchy distortion sounds.
We believe that you, genuine guitarist sticking to the guitar sounds.

Cabinet Section

The cabinet has a proprietary structure “Helmholtz Resonance Cabinet”.
Double buffeled structure actively use its resonance inside.
By making a “resonance space” to utilize the Helmholtz resonance, we succeeded in producing a “sound as instruments”
It pursues its own tone with unique structure that fomore guitar amps could not obtain until now.

image1Japan Patent Office Utility Model Registration No:3200860

In addition, both od inner and front baffles is made of very thin wooden board, which thickness is only 1/8″(3mm).
Thease extremely thin baffle realized the clearness that we had unheard.
And thease baffles sound as well as the sounding board with the acoustic instruments, itself.
As a result, the cabinet emphasizes the instrument-specific sound.

Type-1_CloseUp

 

In the process of development, we collected data of the ultimate acoustic guitar, such as Martin D-45E.MartinD-45E

Learn More “Helmholtz Resonance Cabinet”

Chassis

VirtuosOn_Stable-Cabinet
The chassis are splitted upper amplifier section and lower power supply unit section.

We place the heavy transformer at the bottom of the cabinet, amplifier cabinet is released from the damping effect of the transformer weight.
And then, it is now possible to be sound sonorous tones.
Further, since the surface area of the chassis increases, high thermal conductivity aluminum act as heat sink.
That has ensuring high heat radiation.
Control panel is simple configuration of operation knobs, volume(gain), bass, middle, treble, and master volume.

Acoustic setting
Light Crunch setting
Standard Setting
Jazzy Setting

Available Formats:1*8 Combo
Volume wattage:5W
Power tube type:1x6V6S
Preamp tube type:1x12AX7
Channels:Single
Speaker & Impedance:1×8″ Jensen C8R / 8 Ohms
Current wattage:30W
Dimentions:12″H x 12″W x 12″D (without handles and rubber feets)
Weight:22 Lbs (10Kg)

TYPE-1リーフレット表TYPE-1リーフレット裏

TYPE-1取扱説明書_表TYPE-1取扱説明書_裏

Pedals

Neo-futuristic designed pedals

Manufactured by Hand-Wired. Neo-futuristic designed pedals. Line up contains solid state booster, stompboxes.

Solid Mid Booster
Hand-Wired

Like 70’s traditional booster
Suit for light crunch sound with low gain tube amps.
Players can select 3-mode of normal(mid) – treble – fat sounds.

 

Solid Over Drive
Hand-Wired

An authentic but neo-futuristic designed drive pedal.
Fit for various style guitarists.

 

Solid Distortion
Hand-Wired

Simple & traditional distortion pedal.
Shredding Riffs with easy operation.

Type-M


overvirew

Independent 2 channnels tube amplifier: Aggressive Distortion & Sparking Clean tones.
The cabinet made of aluminum and carbon panels: Unprecedented in the guitar amplifier cabinet structure.
To explore further evolution form our product Type-1, we developed the Type-M-Head and Type-M-Cabinet.
Electrical circuit has 100% tube circuit to amplify sounds.
Amplifier is added in the aggressive distortion circuit to the sparking clean circuit of the Type-1.
Each of preamplifier cannnels have independent circuits.

We restrain the output power to 5W,
because this amplifier and cabinet is developed for the guitarist who pursue earnestly guitar tone and technique at their home.

 

TECHNICAL DETAILSVIDEOSPEC

Type-M-Head

 

Preamplifier section

Of course, Type-1’s electrical circuit has 100% tube circuit to amplify sounds.
Construct this with a hand wired on the turret board.

Turret_Board
The CH-1 and CH-2 are two completely independent preamplifier circuits, including tone circuits are.
CH-1 has two gain stage with single 12AX7 tube,As with Type-1,whitch offers sparkling clean tone with quick responce tubes.
The CH-2 has four gain stages with double 12AX7 tubes.
Its circuit is designed for not only distortion level but sustain feeling, and harmonic overtone characteristic required for a guitar amp.
As a result, CH-2 generates too much deep distortion with its gain knob is over 12 o’clock.
We knowlmost guitarist will not play with such a deep distorted sound, but less gain designed circuit can’t have nice sustain and harmonic overtone.
Learn More How to use CH-2 Distorsion

In order to enable that guitarists can play technical licks which needs effectors such as delay during distortion sound,
Type-M Head equipped with an effect loop.
This effect loop is also composed of single 12AX7 tube buffer circuit and amplification circuit.

Preamplifier section

As mentioned earlier, we restrain the output power under 5W ‘cause this amplifier is a tool for “guitarists who pursue tones and techniques”.
While restraining the output, players can replace power tubes 6V6S(6V6GT) to 6L6GC in order to expand tone variations as well.
As you know, 6V6s and 6L6s tubes has its own proper bias voltage. In generally, players can’t replace 6V6 to 6L6 or 6L6 to 6V6.
Therefore, Type-M-Head equipped with a switch to change the bias voltage.
If you remove the head cover, the switch is in front of the power tube socket.

Metal – band mixed

 

Metal – Riff

<Type-M-Head

Volume wattage:5W
Power tube type:1x6V6S (1x6L6GC avairable)
Preamp tube type:4x12AX7
Channels:2 channels (CH-1/clean CH-2/distortion)
Speaker output jacks:1×8 Ohms 1x16ohms
Current wattage:41W
Dimentions:8″(20cm)H x 16 3/16″(41cm)W x 11 1/16″(28cm)D
Weight:13.5 Lbs (6.1Kg)

Silverwire Cables

silverwire_logo

SilverwireCables_image

 

Point1

Every guitar player, especially professional player knows importance of cables
when they are playing guitars with its great ptentials.
No matter how great the guitars and amplifiers are, the cables could causes sound better or not.
On our long time experience, we producted guitar cables that can express player’s tone absolutely enough.
silverwire01 

Someone shoud know “silver” is best material to transmit very sensitive tone.
Our cable has silver plated OFC inner wiers almost close to the sterling silver for best transmission.
Especially, silver is better than general OFC wiers at transmission high frequency sounds necessary to sound sensitive tone.
This is the reason why that we named “Silverwier” series for our guitar cables.
silverwire02General Cable and Silverwire cable Frequency Response comparison

Point2

The phone-plug is very important to transmit the sounds surely.
We adopted Neutrick’s new brand “REAN” plugs for our guitar cables.
This gold plated plug is realizing stable with tight handles when you plug-in the cable to the amps.

Point3

Soldered with 5.5% silver.
Handcrafted by craftsmen.

Point4

Cable wire is covered with nylon sleeves for protection and cleanness.
The sleeves has selectable colors.

Point5

Of cource, this cables are suitable for professional players, and also amateur players
who will practice to improve their skills well.

Color : Black, Emerald Green
Length : 2m, 3m, 5m
Price : 2m ¥6,800(without tax)
3m ¥8,800(without tax)
5m ¥12,800(without tax)

DRY Jack-clean

DRYジャックリーン
Clean up item for cleaning phone jacks on the amps and guitars.

No chemicals needed, dry-type cleaning.

Reducing zipper noise.

Price :3 pieces ¥800(without tax)